View IP79M05_459903.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

IP120MA SERIES IP120M SERIES IP79M00A SERIES IP79M00 SERIES 0.5 AMP NEGATIVE VOLTAGE REGULATOR
!
2
1
3
FEATURES
Pin 1 - Ground Pin 2 - VOUT Case - VIN Pin 1 - Ground Pin 2 - VIN Case - VOUT
* OUTPUT CURRENT UP TO 0.5A * OUTPUT VOLTAGES OF -5, -12, -15V * 0.01% / V LINE REGULATION * 0.3% / A LOAD REGULATION * THERMAL OVERLOAD PROTECTION * SHORT CIRCUIT PROTECTION * OUTPUT TRANSISTOR SOA PROTECTION * 1% VOLTAGE TOLERANCE (-A VERSIONS) DESCRIPTION
The IP120MA and IP79M00A series of voltage regulators are fixed output regulators intended for local, on-card voltage regulation. These devices are available in -5, -12, and -15 volt options and are capable of delivering in excess of 500mA over temperature. The A suffix devices are fully specified at 0.5A, provide 0.01% / V line regulation, 0.3% / A load regulation, and 1% output voltage tolerance at room temperature. Protection features include safe operating area, current limiting and thermal shutdown.
H Package - TO-39
SMD Package - SMD1 CERAMIC SURFACE MOUNT
GND NC NC VOUT
1 2 3 4
8 7 6 5
NC NC VIN NC
8 Pin J Package
Order Information
Part H-Pack Number (TO-39) IP79MxxAzz IP79Mxxzz IP120MAzz-xx IP120Mzz-xx Note: xx = Voltage Code (05, 12, 15) eg. IP79M05J J-Pack SMD-Pack Temp. CERDIP SMD1 Range -55 to +150C " " " zz = Package Code (H, J) IP120MAH-12
ABSOLUTE MAXIMUM RATINGS (TC = 25C unless otherwise stated)
VI PD RqJC RqJA TJ Tstg DC Input Voltage Power Dissipation Thermal Resistance Junction to Case Thermal Resistance Junction to Ambient Operating Junction Temperature Range Storage Temperature - H Package - SMD Package - H Package - J Package (for VO = -5, -12, -15V) -35V Internally limited 20C / W TBAC / W 120C / W 119C / W -55 to 150C -65 to 150C
Note 1. Although power dissipation is internally limited, these specifications are applicable for maximum power dissipation PMAX of 2W for the H-Package ,1.05W for the J-Package and 15W for the SG-Package.
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk
Prelim. 9/00
IP120MA SERIES IP120M SERIES IP79M00A SERIES IP79M00 SERIES
ELECTRICAL CHARACTERISTICS
Parameter Test Conditions IO = 100mA VO Output Voltage IO = 5mA to 350mA PD PMAX VIN = -7V to -25V TJ = -55 to 150C VIN = -7V to -25V 3 3 5 1 0.1 0.1 40 IO = 300mA IO = 100mA TJ = -55 to 150C 65 65 80 80 1.1 300 0.5 1.0 0.5 2.3 600 1.4 2.0 0.5 300 1.0 0.5 10 10 50 2 0.4 0.4 400 54 54 2.3 600 1.6 dB V mA A mV C 1 50 30 100 2 0.4 mA 0.4 400 mV VIN = -8V to -18V TJ = -55 to 150C -4.85 -5.15 -4.75 -5.25 VIN = -10V IP79M05A IP120MA-05 Min. Typ. Max. -4.95 -5 -5.05 IP79M05 IP120M-05 Min. Typ. Max. -4.8 -5 -5.2 V Units
DVO DVO
IQ
Line Regulation
IO = 350mA IO = 5mA to 500mA VIN = -10V VIN = -10V IO = 5mA to 500mA
Load Regulation Quiescent Current
TJ = -55 to 150C IO = 350mA TJ = -55 to 150C TJ = -55 to 150C VIN = -8V to -25V TJ = -55 to 150C
mV mA
DIQ
Quiescent Current VIN = -10V Change IO = 200mA
VN
Output Noise Voltage
f = 10Hz to 100kHz f = 120Hz VIN = -8V to -18V IO = 350mA VIN = -35V VIN = -10V IO = 5mA
mV
DVIN DVO
Isc Ipk
Ripple Rejection Dropout Voltage Short Circuit Current Peak Output Current
Average Temperature Coefficient of VO
1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp voltage changes due to changes in internal temperature must be taken into account separately. 2) Test Conditions unless otherwise stated: TJ = 25C PMAX = 2W for H Package (TO-39) PMAX = 1.05W for J Package (CERDIP) PMAX = 15W for SMD1 Package (SMD1)
10ms, d 5%). Output
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk
Prelim. 9/00
IP120MA SERIES IP120M SERIES IP79M00A SERIES IP79M00 SERIES
ELECTRICAL CHARACTERISTICS
Parameter Test Conditions IO = 100mA VO Output Voltage IO = 5mA to 350mA PD PMAX TJ = -55 to 150C VIN = -14.5V to -30V 4 4 10 1.5 0.1 0.1 96 IO = 300mA IO = 100mA TJ = -55 to 150C 58 58 72 72 1.1 300 0.5 1.0 1.2 2.3 600 1.4 4.8 0.5 300 1.0 1.2 18 18 60 3 0.4 0.4 960 54 54 2.3 600 1.6 dB V mA A mV C 1.5 80 50 240 3 0.4 mA 0.4 960 mV VIN = -14.5V to -30V -11.64 -12.36 -11.4 -12.6 VIN = -19V IP79M12A IP120MA-12 Min. Typ. Max. -11.88 -12 -12.12 IP79M12 IP120M-12 Min. Typ. Max. -11.5 -12 -12.5 V Units
DVO DVO
IQ
Line Regulation
IO = 350mA IO = 5mA to 500mA VIN = -19V VIN = -19V IO = 5mA to 500mA
VIN = -15V to -25V TJ = -55 to 150C
Load Regulation Quiescent Current
TJ = -55 to 150C IO = 350mA TJ = -55 to 150C TJ = -55 to 150C VIN = -14.5V to -30V TJ = -55 to 150C
mV mA
DIQ
Quiescent Current VIN = -19V Change IO = 200mA
VN
Output Noise Voltage
f = 10Hz to 100kHz f = 120Hz
mV
DVIN DVO
Isc Ipk
Ripple Rejection Dropout Voltage Short Circuit Current Peak Output Current
VIN = -15V to -25V IO = 350mA VIN = -35V VIN = -19V IO = 5mA
Average Temperature Coefficient of VO
1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp voltage changes due to changes in internal temperature must be taken into account separately. 2) Test Conditions unless otherwise stated: TJ = 25C PMAX = 2W for H Package (TO-39) PMAX = 1.05W for J Package (CERDIP) PMAX = 15W for SMD Package (SMD1)
10ms, d 5%). Output
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk
Prelim. 9/00
IP120MA SERIES IP120M SERIES IP79M00A SERIES IP79M00 SERIES
ELECTRICAL CHARACTERISTICS
Parameter Test Conditions IO = 100mA VO Output Voltage IO = 5mA to 350mA PD PMAX TJ = -55 to 150C VIN = -17.5V to -30V 4 4 12 1.5 0.1 0.1 120 IO = 300mA IO = 100mA TJ = -55 to 150C 57 57 70 70 1.1 300 0.5 1.0 1.5 2.3 600 1.4 6.0 0.5 300 1.0 1.5 22 22 75 3 0.4 0.4 1200 54 54 2.3 600 1.6 dB V mA A mV C 1.5 80 50 240 3 0.4 mA 0.4 1200 mV VIN = -17.5V to -30V -14.55 -15.45 -14.25 -15.75 VIN = -23V IP79M15A IP120MA-15 Min. Typ. Max. -14.85 -15 -15.15 IP79M15 IP120M-15 Min. Typ. Max. -14.4 -15 -15.6 V Units
DVO DVO
IQ
Line Regulation
IO = 350mA IO = 5mA to 500mA VIN = -23V VIN = -23V IO = 5mA to 500mA
VIN = -18V to -28V TJ = -55 to 150C
Load Regulation Quiescent Current
TJ = -55 to 150C IO = 350mA TJ = -55 to 150C TJ = -55 to 150C VIN = -17.5V to -30V TJ = -55 to 150C
mV mA
DIQ
Quiescent Current VIN = -23V Change IO = 200mA
VN
Output Noise Voltage
f = 10Hz to 100kHz f = 120Hz
mV
DVIN DVO
Isc Ipk
Ripple Rejection Dropout Voltage Short Circuit Current Peak Output Current
VIN = -18.5V to -28.5V IO = 350mA VIN = -35V VIN = -23V IO = 5mA
Average Temperature Coefficient of VO
1) All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF. All characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tp voltage changes due to changes in internal temperature must be taken into account separately. 2) Test Conditions unless otherwise stated: TJ = 25C PMAX = 2W for H Package (TO-39) PMAX = 1.05W for J Package (CERDIP) PMAX = 15W for SMD Package (SMD1)
10ms, d 5%). Output
Semelab plc.
Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: sales@semelab.co.uk Website: http://www.semelab.co.uk
Prelim. 9/00

▲Up To Search▲

Price & Availability of IP79M05

	To Download IP79M05 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .